41. Jaw angle 3 deg.more than anglepins(<25 degree). 斜面角度要比行位斜邊角度大3度(<25度)。

42. Keep enough space to run waterline atslide /lifter/majorinserts. 在行位、斜頂、主要鑲件處保留足夠位置（空間）布置水槽。

42. Lifter angle less than 15 degree. 斜頂角度小于15度。

43. Lifter rods dia, less than 1". 斜頂桿直徑不能少于1"。

44. Limit switch in tact and protected. 是否已安裝限位制？

45. Moldbase and steel dimensioned. 模坯和鋼料號的標注。

46. Minimum 5 deg.for shut-off. 斜頂鑲件最小5度插穿。

47. Mechanism for sequence？動作機構是否正確？

48. Mold safety straps installed andpainted red？是否已安裝安全帶及噴上正確顏色在模坯上？

49. Mould flow and simulation should becarried out for the bestgate location, filling analysis, pressure distributionand heat distribution. 適宜應用模擬的模具注塑過程，注射分析、壓力分布及溫度分布以確定最佳入水位置、流道尺寸和疏氣位置等。

50. Mould should be designed with maximumcooling and withappropriate amount of ejection points. 模具在設計上要做到盡快冷卻，上、下內模高溫點應該有個別的冷卻，應有適量頂針。

51. Mould should be able to run fullyautomatic. Large part shouldbe picked up by robot. 模具能夠全自動生產，大的零件應由機械手拿出。

52. Mould should be tested to meet adefined Cpk quality standard. 模具經過測試，符合預定的Cpk質量標準。

53. Mould should have safety features toprotect accidental damage,incorrect assembly and set up of mould. 模具應具備可以預防意外損害及錯誤安裝等安全特性。

54. Mould halves requiring accuratealignment of core and cavity,and shut off should have appropriate part linelocks. 上、下模需要精確配合或有擦位的地方，模具一定要有直身鎖。

55. Mould requiring heating should haveinsulator plate. 需要加熱的模具，必須有隔熱板。

56. Mould preferred to run automatic;self-degating wheneverpossible. 模具最好能自動生產，模具盡可能自斷水口。

57. No obstructions on buttom surface ofmold？模具必須穩定位置如有凸出物請加腳座，是否完成？

58. Overall mold size of the moldbase &shut height 模坯長寬和模厚（模架的長寬）

59. Outlets accessible and marked " INOUT and NUMBER"？出入水位有否打上IN 、OUT 字碼？

60. Protruding items shown and protected. 畫出突出部件并做好保護。

模具達人微信：mujudaren

61. Parting line at the acceptable surface.合模分布在合理可接受的表面。

62. Put waterline as much aspossible/wherever possible. 盡可能布置多的運水。

63. Put waterline for slide /lifter/insertwherever possible. 盡可能在行位、斜、鑲件布置運水。

64. Parting line cleared and releasedproperly? 分模線是否正確?

65. Proper locating ring and diameter？定位圈尺寸及直徑是否正確？

66. Proper radius and orifice on spruebushing and keyed.唧嘴R及管釘是否正確？

67. Part line lock recommended when thereis shut off. 當有擦位時，最好有直身鎖保護。

68. Protruding items shown and protected. 如有零件凸出，模坯請加保護物。

69. Proper K.O. holes size and location. 頂棍孔尺寸及位置是否正確?

70. Runners to be balanced. 流道必平衡。

71. Runners cross section type and size asper standard. 流道切面形狀和尺寸符合標準。

72. Runner and parts should be ejectedautomatically .Multipleejection should be avoided. 頂出方法可使流道與產品自動掉下，避免運用多次頂出方法。

73. Sufficient view and section. 足夠的視圖和切面圖。

74. Safety Strap in red. 模塊藏入模坯，要涂成紅色。

75. Standing steel supported to keepstable. 加撐腳以保前、后模能平穩放置。

76. Support pillars>50% part projectionarea , steel :1040。撐頭面積大于50%的產品投影面積，材料：1040。

77. Safety strap clear tie bar? 鎖模塊與哥林柱沖突嗎?

78. Sucker with reverse 10 deg. Undercut.10度倒扣的流道拉料桿。

79. Steel type & hardness of slide&heel blocks. 行位和壓條的料號和硬度。

80. Sufficient stroke oflifters(1/16"+ undercut size)？斜頂是否有足夠的行程（1/16”+倒扣尺寸）？

81. Sufficient stroke for floating plate？浮動板是否有足夠的行程？